Precision Aero Services
FAA Repair Station P0VR332Y
CAGE 665Z9
1323 Hwy. U
Bolivar, MO 65613
Tel: 417.326.2376
Fax: 417.326.2377
Toll Free: 855.727.2376
Our Repair Fleet Experience:
Boeing:
B727, B737, B747, B757, B767, KC135, C17, CH46, CH47
Bombardier:
BD700, CL600, CL601
Dornier:
DORNIER 328
Gulfstream:
G200, GII, GIII, GIV, GV
Hawker:
HS125 600/700, HS125 800/850, HS125 800SP, HAWKER1000
Dassault Falcon:
Falcon 10, Falcon 20, Falcon 200, Falcon 900, Falcon 2000
FAA Repair Station P0VR332Y
CAGE 665Z9
1323 Hwy. U
Bolivar, MO 65613
Tel: 417.326.2376
Fax: 417.326.2377
Toll Free: 855.727.2376
Our Repair Fleet Experience:
Boeing:
B727, B737, B747, B757, B767, KC135, C17, CH46, CH47
Bombardier:
BD700, CL600, CL601
Dornier:
DORNIER 328
Gulfstream:
G200, GII, GIII, GIV, GV
Hawker:
HS125 600/700, HS125 800/850, HS125 800SP, HAWKER1000
Dassault Falcon:
Falcon 10, Falcon 20, Falcon 200, Falcon 900, Falcon 2000
Location
Call us at 417-326-2376 for more information.
Precision Aero Services - Nationwide
Precision Aero Services provides composite repair and aircraft parts to Miami, FL, Los Angeles, CA, St Louis, MO, Dallas, TX, Houston, TX and Las Vegas, NV as well as the surrounding areas.
Precision Aero Services provides composite repair and aircraft parts to Miami, FL, Los Angeles, CA, St Louis, MO, Dallas, TX, Houston, TX and Las Vegas, NV as well as the surrounding areas.
Midwest Aviation Group d/b/a Precision Aero Services Inc. (PAS) is located in Bolivar, Polk County, Missouri on 7 acres. Our 35,000 square foot facility was built in 2002.
Our building includes a shop area which is 32,500 square foot and an office area consisting of 2,500 square foot. The shop facility and office area is constructed of red iron and is metal clad on concrete with numerous overhead doors for shipping and receiving aircraft assemblies. The shop area has extremely good lighting throughout and has single phase and 240/480 volt 3ph to power equipment.
PAS also has a newly constructed 1,500 square foot climate controlled lay-up room which is lighted with approximately 100 foot candle lighting.
PAS equipment includes a new 8’ x 20’ x 7’, 500°F, 480v/3ph, 120KW electric oven, a 17’ x 30’ x 10’ paint booth, a new 7’ x 7’ walk-in freezer, a 480v/3ph 50HP Ingersoll Rand air compressor/ dryer combination and two (2) 660 gallon receiver tanks connected in series to 2” airlines supported from the building ceiling structure with drops at all internal columns, a 480v/3ph 7HP vacuum pump mounted on a 50 gallon tank with drops at various locations within the lay-up room, a 240v/3p 15HP milling machine, and several metal forming equipment including various brakes, stretchers, shrinkers, grinders, and sanding devices along with numerous heavy duty storage racks to ensure proper storage of components. In addition, we have numerous dies, an ESAB MultiMaster 260 MIG/TIG/Stick welder, an electric over hydraulic pipe/tubing bender capable of bending up to 2”diameter pipe, an oxy/acetylene cutting torch, and various electric and battery powered hand tools enabling us to perform our own electrical and mechanical repairs or additions as needed.
Our building includes a shop area which is 32,500 square foot and an office area consisting of 2,500 square foot. The shop facility and office area is constructed of red iron and is metal clad on concrete with numerous overhead doors for shipping and receiving aircraft assemblies. The shop area has extremely good lighting throughout and has single phase and 240/480 volt 3ph to power equipment.
PAS also has a newly constructed 1,500 square foot climate controlled lay-up room which is lighted with approximately 100 foot candle lighting.
PAS equipment includes a new 8’ x 20’ x 7’, 500°F, 480v/3ph, 120KW electric oven, a 17’ x 30’ x 10’ paint booth, a new 7’ x 7’ walk-in freezer, a 480v/3ph 50HP Ingersoll Rand air compressor/ dryer combination and two (2) 660 gallon receiver tanks connected in series to 2” airlines supported from the building ceiling structure with drops at all internal columns, a 480v/3ph 7HP vacuum pump mounted on a 50 gallon tank with drops at various locations within the lay-up room, a 240v/3p 15HP milling machine, and several metal forming equipment including various brakes, stretchers, shrinkers, grinders, and sanding devices along with numerous heavy duty storage racks to ensure proper storage of components. In addition, we have numerous dies, an ESAB MultiMaster 260 MIG/TIG/Stick welder, an electric over hydraulic pipe/tubing bender capable of bending up to 2”diameter pipe, an oxy/acetylene cutting torch, and various electric and battery powered hand tools enabling us to perform our own electrical and mechanical repairs or additions as needed.
